“K线走完模式”转换成“固定轮询模式”或者“混合模式”的方法
以便把各个模型放在同一个框架内进行图表程序化交易
举例：
均线交叉模型（K线走完模型）：
runmode:0;
ma5:=ma(c,5);
ma20:=ma(c,20);
entertime:=time>100000 and time<144500;
if holding>0 and ma5<ma20 then sell(1,1,market);
if holding<0 and ma5>ma20 then sellshort(1,1,market);
if holding=0 and ma5>ma20 and entertime then buy(1,1,market);
if holding=0 and ma5<ma20 and entertime then buyshort(1,1,market);
if time>=150000 then begin
sell(1,1,market);
sellshort(1,1,market);
end
简单的改法，自然是把各个条件“过去化”，如：ma5 改为 ref(ma(c,5),1);但这种方法碰到大型的、复杂的模型时，容易出错
可采用这种方法，把holding用全局变量cc替换，然后加入红色部分代码，红色部分代码要放在信号语句的前面：
runmode:0;
variable:cc=0;
ma5:=ma(c,5);
ma20:=ma(c,20);
entertime:=time>100000 and time<144500;
if holding>0 and cc<=0 then sell(1,1,limitr,o);
if holding<0 and cc>=0 then sellshort(1,1,limitr,o);
if holding=0 and cc>0 then buy(1,1,limitr,o);
if holding=0 and cc<0 then buyshort(1,1,limitr,o);
if cc>0 and ma5<ma20 then cc:=0;
if cc<0 and ma5>ma20 then cc:=0;
if cc=0 and ma5>ma20 and entertime then cc:=1;
if cc=0 and ma5<ma20 and entertime then cc:=-1;
if time>=150000 then begin
cc:=0;
end
那么，如果是 K线走完模式和盘中模式并存，怎么做呢？也简单，就是在“开盘价下单语句”后面加入蓝色部分的“盘中下单语句”就行了
如下：
runmode:0;
variable:zs=0,cc=0;
ma5:=ma(c,5);
ma20:=ma(c,20);
entertime:=time>100000 and time<144500;
if holding>0 and cc<=0 then sell(1,1,limitr,o);
if holding<0 and cc>=0 then sellshort(1,1,limitr,o);
if holding=0 and cc>0 then buy(1,1,limitr,o);
if holding=0 and cc<0 then buyshort(1,1,limitr,o);
if cc>0 and l<zs then begin
sell(1,1,limitr,min(o,zs-0.6));
cc:=0;
end
if cc<0 and h>zs then begin
sellshort(1,1,limitr,max(o,zs+0.6));
cc:=0;
end
if cc>0 and ma5<ma20 then cc:=0;
if cc<0 and ma5>ma20 then cc:=0;
if cc=0 and ma5>ma20 and entertime then begin
cc:=1;
zs:=c-10;
end
if cc=0 and ma5<ma20 and entertime then begin
cc:=-1;
zs:=c+10;
end
if time>=150000 then begin
cc:=0;
end
